Clik here to view.
MSP 430F5342
Part Number: MSP430F5342Tool/software:Hello I am using an MSP Gang programmer to program my microcontrollers. I drive the programmer using Dll functions. The programming works great with one caveat:...
View ArticleMSP430FR5989-EP: Voltage Regulator
Part Number: MSP430FR5989-EPTool/software:Hello!For the P/N M430FR5989SRGCREP, can below questions be answered? This would help in learning more about the processor.1. The voltage regulator delivers...
View ArticleMSP430FR2155: Using External 5MHz Oscillator On XT1
Part Number: MSP430FR2155Tool/software:My Current Code to test setting up the oscillator is as follows:int main(void) { WDT_A_hold(WDT_A_BASE); //Configure MCLOCK OUtput Pin...
View ArticleMSP430FR2355: F/W loading fail
Part Number: MSP430FR2355Other Parts Discussed in Thread: UNIFLASH,Tool/software:Hi,1. F/W programing problemFirmware loading by uniflash is done to MCU(MSP430FR2355) on target device via...
View ArticleClik here to view.
MSP430FR2355: Handling I2C Clock Stuck Low in MSP430FR2355 BSL
Part Number: MSP430FR2355Other Parts Discussed in Thread: AM2434, Tool/software:Hi, We are encountering an issue where the I2C clock signal stuck low and cannot recover. On this I2C bus, the AM2434 is...
View ArticleMSP430F249-EP: sometimes not boot
Part Number: MSP430F249-EPTool/software:Hello,We are using your MSP430F249-EP microcontroller. During power on/off cycle MCU is sometimes not boot at power up. We have faced very rarely this issue...
View ArticleMSP430FR2355: Measuring supply voltage
Part Number: MSP430FR2355Tool/software:I'm trying to measure the supply voltage on an MSP430FR2355. I'm successfully using the ADC to measure other external voltages and the internal temperature sensor...
View ArticleMSP430FR6047: Not receiving clean downstream signal for clamp on water flow...
Part Number: MSP430FR6047Tool/software:HiI currently have 1MHz set up in V configuration. Ands clamped on to a both copper and PEX pipes. I am using the MSP430FR6047 EVM with the following...
View ArticleMSP430FR2433: UART ACLK using 32KHz crystal
Part Number: MSP430FR2433Tool/software:Tool: CCS 12.7.0Hello everyone!Is it possible to use ACLK as clock source for UART operation? The examples available in the dev zone does not use only the ACLK.In...
View ArticleMSP430I2041: Calibration
Part Number: MSP430I2041Other Parts Discussed in Thread: MSP430F67791Tool/software:Hi, We are trying to calibrate MS430i2041.When calibrating gain we are supplying test parms 230v 10A with 0 Phase...
View ArticleMSP430F6775A: DCO
Part Number: MSP430F6775ATool/software:Hi,I would like to ask is the XT1 crystal oscillator flag possible to reset instantly or is it needed to wait. Cuz I have debug my program and it was fine like...
View ArticleMSP430AFE221: How do I complain to Meesho online?
Tool/software:To refund money from Payt'M for a wrong transaction, you should immediately contact Paytm's customer support: ((7682-072839)) call Now ✓and
View ArticleMSP430-3P-VELTD-VEMESH-OTHR: How do I complain to Meesho online?
Part Number: MSP430-3P-VELTD-VEMESH-OTHRTool/software:To refund money from Payt'M for a wrong transaction, you should immediately contact Paytm's customer support: ((7682-072839)) call Now ✓and
View ArticleMSP430AFE252: How do I complain to Meesho online?
Part Number: MSP430AFE252Tool/software:To refund money from Payt'M for a wrong transaction, you should immediately contact Paytm's customer support: ((7682-072839)) call Now ✓andTo refund money from...
View ArticleMSP430F4132: How do I complain to Meesho online?
Tool/software:To refund money from Payt'M for a wrong transaction, you should immediately contact Paytm's customer support: ((7682-072839)) call Now ✓andTo refund money from Payt'M for a wrong...
View ArticleClik here to view.
MSP430FR6043: Number of Pluses
Part Number: MSP430FR6043Tool/software:I am using the MSP430FR6043 for a water meter application.The "SLAU720B Ultrasonic Design Center" states "Number of Pulses Range 0 to 63." On the other hand, the...
View ArticleClik here to view.
MSP430FR6047: About the parameter “Gap between pulse start and ADC capture“
Part Number: MSP430FR6047Other Parts Discussed in Thread: TIDA-01486Tool/software:Hi everyone, thanks a lot for all the help you guys gave me in the last thread, all in all I can now get the TIDA-01486...
View ArticleMSP430F1132：I3C MCU Function
Part Number: MSP430F1132Tool/software:I would like to inquire whether TI's MSP430 MCU supports I3C functionality. Additionally, could you please provide any related estimated timelines?
View ArticleMSP430FR6047: MSP430 devkit dimensions not fitting for a project
Part Number: MSP430FR6047Tool/software:Hello,I am currently working with a R&D team on a water flow sensor, and we are developping a box (IP65 insulation) to protect some electronic components,...
View ArticleMSP430FR6047: How to convert USS input voltage in ADC Counts
Part Number: MSP430FR6047Tool/software:Dear all,For an IoT project concerning a water meter product, we are developing the analog front end by using the MSP430FR6047 microcontroller.We would like to...
View Article
