MSP430FR2475: Inquiry about multiplexed pins for JTAG and UCA0
Part Number: MSP430FR2475Our customer plans to develop their system with MSP430FR2475TPTR(48pin). They would like to use UCA0 (UART or SPI), but, those pins are multiplexed with the JTAG Standard...
View ArticleMSP430FR5949: The equipment field operation has a small probability, ADC12...
Part Number: MSP430FR5949 #define CALADC12_25V_30C *((unsigned int *)0x1A22) // Temperature Sensor Calibration-30 C #define CALADC12_25V_85C *((unsigned int *)0x1A24) //See device datasheet for TLV...
View ArticleMSP430FR5994: BQ daisy chain
Part Number: MSP430FR5994I tested a daisy chain of 3 custom BQ79616 MBBs connected to BQ79600 and MSP430 (SPI interface on custom PCB). One of the MBBs (device 2 in the middle of the daisy chain) has a...
View ArticleMSP-FET: Powering the Target Processor with MSP-FET
Part Number: MSP-FETOther Parts Discussed in Thread: UNIFLASHIs is possible to Power the MSP430 with the MSP-FET programmer. I can get my device program when it's powered externally, but it would be...
View ArticleClik here to view.
MSP430FR6047: One channel captured correctly, while the other one not
Part Number: MSP430FR6047Hello,I am trying to analyze two 2MHz transducers in water using the MSP4030FR6047.However, I am not able to see the capture signal for one of the transducers, while for the...
View ArticleEVM430-FR6047: "Volume Flow Rate" calculation method
Part Number: EVM430-FR6047Dear person in chargeWe are currently using EVM430-FR6047 for development and evaluation.I would like to confirm the calculation method of "Volume Flow Rate", is the...
View ArticleMSP430FR5994: dumping register values
Part Number: MSP430FR5994Hi, I am a beginner working with MSP430FR5994 to generate a 1KHz trigger and read voltage values using the ADC. I have the code working where I am able to see the voltage read...
View ArticleMSP-GANG: We can program MCU with MSP-FET but not with MSP-GANG
Part Number: MSP-GANGOther Parts Discussed in Thread: MSP430F2112, , MSP-FETHello, we are moving into production with our MSP430F2112 code and have exported the txt hex file from Code composer. We are...
View ArticleClik here to view.
EVM430-FR6047: About GUI Based Gain Control
Part Number: EVM430-FR6047The Quick Guide says that GUI Based Gain Control should be set within ±900 of the ADC amplitude, but why should it be less than ±900?What is the reason for setting it below...
View ArticleMSP430FR5969: checksum calculation
Part Number: MSP430FR5969Other Parts Discussed in Thread: MSP-FETHi,I am working on a counter project in this microcontroller, the project is completed we are flashing the program through MSP-FET from...
View ArticleMSP430FR6047: How to change the USS parameters without using Ultrasonic...
Part Number: MSP430FR6047Hi Everyone,I am trying to change the USS parameters Transmit frequency, gap between pulse start and ADC capture, number of pulses, UPS and DNS gap, UPS0 and UPS1 gap and gui...
View ArticleClik here to view.
MSP-EXP430FR2433: why multiply to 0.97
Part Number: MSP-EXP430FR2433Hi Team,https://dev.ti.com/tirex/content/msp_academy_msp430_1_00_06_29/modules/msp430/msp430_timer_capture_training/msp430_timer_capture.htmlsignalFreq = (1000000 / sum) *...
View ArticleEVM430-FR6047: About UPS and DNS Gap
Part Number: EVM430-FR6047I would like to confirm something about UPS and DNS Gap.I am aware that if this value is too small, the UPS echoes will remain as noise and affect the DNS waveform, am I...
View ArticleHow Many Data/values per second are transferred to GUI from the EVM430-fr6043?
Part Number: EVM430-FR6043Hi, I want to know how much data/values are transferred to the GUI from the EVM in one second? The data includes DTOF, ATOF,VFR. Can This data transfer increased/decreased in...
View ArticleMSP430FR2632: erased/disabled BSL behavior on BSL entry sequence
Part Number: MSP430FR2632Hello,I had a question on the behavior of an MSP430FR2632 with an empty or disabled BSL region. The TRM says that any attempt to access this region if the bootloader is...
View ArticleMSP430FR5994: Conversion of the ADC output values
Part Number: MSP430FR5994Hi, I am reading the ADC output from ADC12MEM0 but I am confused about the conversion into voltage values. I went through the datasheet and am ending up with weird voltage...
View ArticleMSP430F5359: About the BSL scripter and the COM port number (windows)
Part Number: MSP430F5359Hi.I have a custom board running a MSP430f5359, that can and is upgraded via BSL_Scripter.It all works fine as long as the COM port number is different than "1".When the COM1 is...
View ArticleClik here to view.
MSP430F5438A: I2C USCI30 Errata workaround
Part Number: MSP430F5438AHi, I have observed that my I2C bus is hanging on the 7th bit of the second byteI saw the USCI30 errata so I tried to implement the workaround case 8u: // Vector 8: STPIFG if...
View ArticleMSP-FET430UIF: MSP-FET430UIF
Part Number: MSP-FET430UIFOther Parts Discussed in Thread: MSP-FET, UNIFLASHHi GuyI would like to know if the MSP-FET430UIF is again compatible with development toolsIAR and CODE COMPOSER, because...
View ArticleMSP430F5329: 1MΩ pull-down resistor on pin 63
Part Number: MSP430F5329Other Parts Discussed in Thread: MSP430F5529,Hello,It is recommended to connect a 1MΩ resistor to ground on pin 63 (PUR) of the MSP430F5529 if the USB interface is not used. Can...
View Article