Clik here to view.
MSP430G2001: MSP430G2001
Part Number:MSP430G2001New to this product (MSP-EXP430G2 LaunchPad Development Kit, Rev 1.5 ) . Can the 10-pin female connectors on the bottom of the board be removed (break-off or unsolder?). Need...
View ArticleMSP430F6736: MSP430 DVCC rising voltage rate
Part Number:MSP430F6736HelloI'm using MSP430F6x with Li-ion battery power.I'd like to know, when the battery is empty, and the power output is 0 volt, I'm charging the battery, soon, output is rising 0...
View ArticleMSP430FR2311: Sending Binary Data through UART
Part Number:MSP430FR2311Hi,I am sending Binary data through UART and I am sending my unsigned integers as 2 8 bit values as the TX buffer is only 8 bits. How is it possible to send those two values...
View ArticleReading and Writing to FRAM2 on MSP430FR5994
So I am attempting to read and write large multidimensional signed int arrays (200kB worth) to FRAM to my application. So far I have been successful in creating an array that is 6000x4 and initializing...
View ArticleCCS/MSP430FR5949: MSP430FR5949DA
Part Number:MSP430FR5949Tool/software: Code Composer StudioHi,I started a program using CCS7 and the MSP430FR5949DA and ran into a strange init behaviour.If I init port PJ, PJ.4 and PJ.5 seem to stay...
View ArticleClik here to view.
MSP430FR5994: DMA/FRAM Wake up charge from LPM3
Part Number:MSP430FR5994Hi, im trying to make sense of the wake up figures in the datasheet. I measured around 23nC for wake up from LPM3 which is close to the figure below (but a bit confused about...
View ArticleMSP430FR6989: Why clearing the LOCKLPM5 bit after configuring the I/Os in...
Part Number:MSP430FR6989I'd like to know why should I do this before instead of after if this bit unlocks the I/Os.
View ArticleMSP430 power management
Have msp430 a provision to immediately switch to battery when system voltage is low or absent？How do it？thanks
View ArticleMSP430F2416: Can we reduce the interrupt latency period
Part Number:MSP430F2416Hi all,As far as my understanding about Interrupt latency is " The time taken to execute the ISR from the time of interrupt occurs and we can't reduce this time period". Is this...
View ArticleMSP430F5338: SMCLK status in LPM2
Part Number:MSP430F5338Hi all,I am referring the data sheet SLAS721D –AUGUST 2010–REVISED DECEMBER 2015. In this document section 6.4, there is a description available for Low Power modes. In this from...
View ArticleMSP-GANG: Possibel to put programmer connections into high-impedance state
Part Number:MSP-GANGTeam,my customer is using the MSP-GANG to program 8x MSP430FR6988 in parallel in their own application via JTAG.Due to mechanical reasons it would be an advantage to leave the...
View ArticleMSP430F5529: USB for iAP2
Part Number:MSP430F5529HiMy customer is the partner of apple and being the MFi member, he wants to use MSP430F5529's USB Port to implement a customize USB Class but will not use the HID/CDC/MSC class,...
View ArticleCCS/MSP430G2553: MSP430G2553 in I2C-Slave mode,the program go to transmit...
Part Number:MSP430G2553Tool/software: Code Composer StudioI'm using MSP430G2553 in I2C-Slave mode and I have enabled UCB0TXIE bit.Now the master device can receive the right data from the slave device,...
View ArticleMSP430FR5969: Read multiple bytes of data i2c with repeated start and without...
Part Number:MSP430FR5969I build two functions for reading and writing a single byte using the eusci i2c interface.I was not able to find any examples that did not use interrupts so I build my own.I did...
View ArticleCCS/MSP430G2553: Working MSP430g2553 Hang
Part Number:MSP430G2553Tool/software: Code Composer StudioI am using msp430g2553 controller, some time my working device stop sending uart data, even not revived extern interrupt but after one power...
View ArticleMSP430F2618: Interrupts
Part Number:MSP430F2618Hello!I am using YF‑S201 water flow sensor to measure the flow of water and read the data into msp430f2618 board. I referred to a code written for the same sensor for the...
View ArticleClik here to view.
MSP430F6736: Is my signal wave form is OK?
Part Number:MSP430F6736Hello.I have a question.When device power on, the DVcc signal is the figure like following.SVSh is enabled.SVSh on Voltage is set to 1.65V(typ), SVSh off Voltage is set to...
View ArticleClik here to view.
MSP430FR2633: I/O = "State held" in LPM3 /LPM4 / LPM3.5 / LPM4.5
Part Number:MSP430FR2633Hello,Could you please tell me the meaning of the words "State held" in the LPM modes ?What is the difference against the "On" in the AM mode ?
View ArticleMSP430FR2433: Byte size used for memory size specified for device?
Part Number:MSP430FR2433Hi folks,Just checking out some MSP430 parts on the TI website and note that while the MSP430 is a 16-bit architecture, the datasheet (from a very quick perusal) does not...
View ArticleClik here to view.
MSP430G2553: Blow the JTAG Pin
Part Number:MSP430G2553Hello, I am using MSP430 kit (MSP430G2553 MCU) and CCS software in my project. I want to blow the JTAG pin(Fuse) after loading the code in it. Is MSP-Gang Programmer...
View Article