MSP430: Error initializing emulator: Could not communicate with FET
When I debug it shows error as "MSP430: Error initializing emulator: Could not communicate with FET" .How to solve this..?Plz provide me a solution ASAP.Thank you.
View Articlemsp430f5529 with ADC12MEM1
Hi,I want to use P6.4 as one of the analog input and i need to take this signal from channel say channel 4,then i need to store it in ADC12MEM1.So is my below code works for the same .thank...
View ArticleClik here to view.
Forth compiler
Hi all, For those of you who like to try something else.Try our noForth compiler available for free and ii runs on several MSP430 MPU's. Look here: http://home.hccnet.n...of/noforth.htmlWell documented...
View ArticleVA LCD support
Hi,does the MSP430 LCD interface support VA (Vertical Alignment) LCD? Have we ever tested it before?Thanks.
View Article4- wire Jtag with MSP432
Hello Team,I have a customer who is looking at our MSP432 for their next design. They have questions on the 4- wire JTAG interfacing for this device. The specific question was when using 4 wire JTAG,...
View ArticlePort Damage I2C MSP430G2553
Using MSP430G2553Up to 10 PCBA'a in a daisy chain. Short 4" cables in between. Power / ground is also daisy chained. Voltage drop on power is 30mV through all board (not each). Local regulation would...
View ArticleUnused LCDCAP/R33 pin in MSO430FR6979
Hi Ti MembersWe are using MSP430FR6979 in our project.We are using LCD with I2C interface not with the LCD interface already in the controller.Please suggest what we have to do with LCDCAP/R33 pin if...
View ArticleMSP430F5529 2 ADC12MEM Registers
Dear sir,I want to use two channels for ADC input and am storing it to ADC12MEM0 for channel 0 (p6.0) AND ADC12MEM1 for channel 4(p6.4) .I am using P6.0 as channel 1, and P6.4 as channel 2,I dont know...
View ArticleCommerical use of MSP430G2 LaunchPad Value Line Development kit
Hi, I would like to use the MSP430G2 Launch pad in a commercial product with a Booster pack. Are there any restrictions from TI. Also do the launch pads bear any certifications i.e. CE marking ( for...
View ArticleI2C BSL Rx Password command is acknowledged with 0x52 (wrong checksum)
With MSP430FR68791 I enter the BSL by sending the BSL sequence (RSTN/TEST).After this, I send the Rx Password command frame. This frame is always acknowledged with 0x52 (wrong checksum).As I use the Rx...
View ArticleMSP430 launchpad virtual com port on windows 10
Hi everybody,I use launchpad as virtual com port (com3) and it worked well on windows 7 but after having updated to windows 10 the communication no longer works.Launchap is detected as com3 but don't...
View ArticleSPI slave in Low power
Hi,I'm evaluating the design for low power application. Two MSP430 connected over SPI . One being master and other being slave.I want the slave MCU to wake up on the receiving the byte from master....
View ArticleEVM430-F6779
We have the EVM430-F6779 development board, and I am experimenting with that board but do not succeed everything.What I have done so far:I have connected the board with RS232 cable to the pc RS232 com...
View ArticleClik here to view.
Reset is not stable, MCU is not power up normally
Dear everyone, I have problem with my design (MSP430G2553 chip), after powering, sometimes the MCU worked, sometimes it's not. Sometimes, when I use my hand touch to the SWD pins it worked as...
View ArticleMSP-FET430UIF DEBUGGER ISSUE
Hai...i am started working on MSP436F249 controller and I am using MSP-FET430UIP debugger to program this chip. while application developing suddenly a high voltage is cumming to my target board...
View ArticleMSP430G2553 Launchpad does not connect when P1.6 jumper is open
Hi, I complied and loaded a program using MSP430G2553 Launchpad. I want to use a booster board and have to remove jumper P1.6. As soon as I remove jumper P1.6 the board can no longer talk to CCS CCS...
View ArticleTI MCU to control 2 cylinder engine
Hi team,Please help to recommend TI MCU which is use to control 2 cylinder engine, with EASA DO-178 level B validation. The competitor part is NXP MCP57XX.Hope to hear from you soon.Thanks.
View ArticleMSP430G2231 SPI to DAC help
Hey all, I've done some tinkering with Arduino in the past, and this is my first time tinkering with the MSP launchpad. Right now, I'm trying to use my MSP430 to control a DAC (MCP4921) using SPI....
View ArticleMSP430F5XXX JTAG Programming Security
I am to use MSP430F5247 for a mass production device. I would like it to lock the JTAG communication so no one customer can read or write on the Flash of the microcontroller. Nevertheless, for customer...
View ArticleCapturing data from external parallel ADC with DMA transfer?
MSP430F6736 (actually, any MSP430F5/6 with DMA)TI ADS7882 12 bit ADC with parallel interfaceOur application requires very fast data transfer from the external ADS7882. There are 12 data lines (12 bit...
View Article