Part Number:MSP430F5659
Tool/software: Code Composer Studio
Hi Everyone,
I know that serial communication is very much often. But what about parallel communication.
I want to send and 16 Bit data parallel through 16 port pins at the same time
so is it possible to send and read 16 bit data through 16 port pins?
can anyone help me to find the answer of this question?
Part Number:MSP430G2452
Hi All,
Customers are going to coat the MSP430 with resin as an alternative to a shielded case when using wireless. Is there a recommended coating agent?
I have told that there are no recommended items, but if there is information such as materials and materials, please let me know.
Best Regards,
Takashi
Part Number:MSP430F4270
Hello, we do not use LCD panel on our MSP430F4270 board.
How is pin LCDREF/R13 disposal?
I could not find it out on the MSP430F4xxx UG: http://www.ti.com/lit/ug/slau056l/slau056l.pdf
My understanding is that LCDREF/R13 should be connected to GND(VSS).
Am I right?
Best regards,
ay0689
Part Number:MSP430FR2633
Tool/software: Code Composer Studio
Hello,
I am using captivate -phone board. Sensors used are numeric keypad and proximity sensor. I would like to know how to enable and disable the proximity sensor.
Part Number:MSP430FR2355
Tool/software:TINA-TI or Spice Models
Hi,
I'm currently working with the MSP430FR2355 Smart Analog Combo.
Are there SPICE-Models for the OpAmp, preferably in PSPICE/LtSPICE format?
I only found models for the FR2310, but its OpAmp has different characteristics according to the datasheet, notably a higher GBW. And they are only for TINA-TI.
Best regards
Markus
Part Number:MSP430F5510
Tool/software: Code Composer Studio
Hello.I am facing the same issue.My Jtag id is also not returned .I using Msp430f5510 as a host and msp430f5308 as a target.If any one find this solution problem please inform me Thanx.
Part Number:MSP430F5510
Tool/software: Code Composer Studio
I am facing the same issue .Can you please explain a little bit more ,i am using msp430f5510 as a host and msp430f5308 as a target.I am also using 12 MHZ clock only .
Part Number:MSP430F5510
Tool/software: Code Composer Studio
Hello.Can you please gzuide me how did you generate that graph using Osciloscope .I am still working on it but gettting nothing on Oscilloscope when i check Test and Reset Signal on it.
Part Number:BOOST-DRV8711
Tool/software: Code Composer Studio
trying to get a the DRV8711 + MSP430-EXP430G2ET running first time.
Motor and power supply connected
set up the Hardware/Software as advised in User's Guide SLVU967–May 2014.
The Gui is running and seems connected with the DRV8711 Controller. But the Software Buttons are not working .
Another indication for dysfunction is the emty Firmware Version window and and full scale current widow.
Can you help me to get it run , any clue ?
Part Number:EVM430-FR6047
Tool/software: Code Composer Studio
Hello guys.
I've been trying to debug my evm430 board, and I've got some issues here. I downloaded the code:
available on "http://software-dl.ti.com/msp430/msp430_public_sw/mcu/msp430/USSSWLib/USSSWLibWater/02_20_00_16/index_FDS.html", and started a debug section on CCS 8.1.0. The problem is, when I hit the pause button, a message is shown:
And:
I don't know what can I do. The leds from the board are not blanking. In resume, nothing happens on the board. The code is below. Thank you guys for your help.
Best regards, William.
Part Number:MSP430FR5994
Tool/software: Code Composer Studio
Hi,
I want to read the value of some variables saved in FRAM after the MCU finishes its task. When the MCU is doing the task, it is powered by an external capacitor. After the task is finished, I want to check the result which is saved in FRAM.
I only know that we can see FRAM values in CCS debug mode by using the "Memory Brower". But entering the debug mode, CCS will re-program the MCU so that all previous data will be erased.
Is there any possible solution for my case?
Thanks,
Yubo
Part Number:MSP430F5326
Hi
Please Help solve the problem. Thanks a lot.
1. The hardware connection is: battery power supply (3.3v) - > button switch (0.5 internal resistance) - > MSP430F5326.
2. The following figure is the voltage change of OBU when it is powered on. After 5326 is powered on, there is a certain proportion of current that lasts 200 mA, but it does not crash and can work and sleep normally. Even if it is hard reset, the current of 200 mA will continue. At the same time, 5326 is very hot. Later, it is found that the voltage drop at the instant of power-on is very large, and it is suspected that the large voltage drop caused 5326 abnormality.
3. Functionally, it has been found that AD is abnormal. It was originally used to measure voltage by AD. If 200 mA occurs, hard reset can not be restored.
4. The impedance of the power supply circuit is only 0.5, which has been confirmed.
Part Number:MSP-GANG
Hi,
I have recently set up and connected the msp gang. And having issues with it connecting via error #23.
Our prog. file is hex.
No external power source.
I have done the following from reading up on other forums, is it worth investigating more or returning back for a replacement?
1) Various voltage/reset/JTAG speed adjustments.
2) connected the cap and resistor across the Vcc and RST.
3) Shortened cable length.
Please advise.
Part Number:MSP430FR6043
GAS flow measurements are performed on a pipe with 200-kHz, 400-kHz, and 500-kHz transducers available from Jiakang, Hurricane, CeramTec, and Audiowell.
How do different frequencies affect measurements?Which frequency has the best accuracy theoretically?
And where to download the 3D printable pipe design?
Part Number:MSP430F5510
Tool/software: Code Composer Studio
Hello .i am working on Replicator Project Xv2 slau320.I have set all ports and Clock according me my Requirements.But when i try to debug the code ,My code gives error on GET JTAG ID .Any one have experience the same problem .Please help me with this .Thank you
Part Number:MSP430I2041
Tool/software: Code Composer Studio
Hello Sir/Mam,
I am trying to program MSP430I2041 with isolator ISO1540DR for SBWTCK and SBWTDIO lines. Launchpad ,I am using for programming is MSPEXP430F5529LP.
Without Isolation, I am able to program MSP430I2041 through CCS. But i am not able to program it through CCS with isolation.
For reference , Schematic snippet is attached here (Please note that ,actual IC used is ISO1540DR and not ISO1541DR as shown in schematic) along with CCS programming error message.
CCS Error Comes Like this ...
Please let me know if anything wrong in schematic, that is affecting MSP430I2041 programming.
Thanks and Regards,
Fakruddin Mulla
Part Number:MSP-GANG
Hi,
I have recently set up and connected the msp gang. And having issues with it connecting via error #23.
Our prog. file is hex.
No external power source.
I have done the following from reading up on other forums, is it worth investigating more or returning back for a replacement?
1) Various voltage/reset/JTAG speed adjustments.
2) connected the cap and resistor across the Vcc and RST.
3) Shortened cable length.
Please advise.
Part Number:MSP430F5438
Hello,
I am currently trying to figure out how to make my scripter work with my MSP430F5438. I have an FTDI cable to my PC via USB and have its RX and TX lines going to P1.1 and P1.2 which are respectively the BSL's default UART pins as well as the ground from the FTDI wire hooked up to the ground of the MSP430F5438 (For reference, I am using the msp5438STK by Olimex).
Here is a look at my script:
bsl_script_1.txt
MODE 543x_family UART 9600 COM26
CHANGE_BAUD_RATE 9600
RX_PASSWORD bsl_pass.txt
MASS_ERASE
TX_BSL_VERSION
REBOOT_RESET
as well as my bsl_pass.txt
@FFF0
FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
q
using my script, i get the following message:
Port 26 is the port of my FTDI cable.
Please let me know if there is a way to fix this.
I currently also have the MSP-FET, however I cannot seem to get that to work at all. I would receive the same message on that one as well. Based on previous forum posts, I cannot find my MSPApplication UART from device manager and can only see MSP-FET430UIF - CDC (COM25)
Thank you for taking your time in reading this post.
Nick
Part Number:MSP432P401R
Tool/software: Code Composer Studio
Dear Sir:
do you have any suggestion for the external crystal using that the temperature rage between -40~85 C or AEQ-2000.
Thanks you.
Part Number:CC2531
Tool/software:TINA-TI or Spice Models
Hi. I am using a packet sniffer program using the TI CC2531 product.
However, during use, the next toolbar disappears and seven menus, including the capture device, are not available.
Is there a way to reset the toolbar to view?
Below is the current view at run time.
