How to build a Look Up Table with CCS 6.2 assembly code?
I will like to using Assembly code to build a Look Up Table for output a Sine wave, which complier is CCS V6.2.Please help me to correct below program and instruct.Thanks your help....
View ArticleProblem with Auto Addressing in MSP430 DALI stack(MSP430G2553)
Hello All,I am facing issues with Auto Addressing with TI MSP430 DALI stack. I have tested the same with 3 different DALI controllers, but the DALI device is not getting addressed whatsoever. If there...
View ArticleFri Oct 14, 2016 10:54:22: No state storage buffer implemented on connected...
hello,i'm seeing the above error mentioned in the subject line while trying to run sensor moniotor program on MSP430F2274 (ez430-RF2500) in IAR IDE EW MSP430 6.50.1 though the option for enabling...
View ArticleClik here to view.
MSP430FR6877 BSL JTAG
Hi Champs,My customer is designing water meter using MSP430FR6877. MSP-GANG is used to program the MCU. They have tried JTAG and BSL downloading. The content of 0xFF90 was different comparing 2...
View ArticleSuggestion to shorten CC430 shut down time after power cut off
Hi Sir,My customer using CC430 to design for data transmission.CC430 is powered by battery and the battery is connected to the circuit via a mechanical switch.In customer program, the CC430 will stay...
View ArticleQuestions for eCOMP operation in LPM3
Hi, My customer is using MSP430FR2311 and planning to use comparator(eCOMP) in LPM3. Q1) Is there any slew rate(usec/V) specification for input signals ? Customer wants to know both High-speed mode and...
View ArticleSystem with two MSP devices
Hi, In my customer’s system, there are two MSP devices on one board. One is F5255, another is FR2311. Both MSP devices share the same power supply (2.5V) and connected via UART interface. Each software...
View ArticleClik here to view.
error in flashing MSP432P401R revison c
Hello ,I am getting the below error during the debug process, error in loading the programCORTEX_M4_0: Flash Programmer: Reading HW revision failed.CORTEX_M4_0: Your XMS432P401R material is no longer...
View ArticleStoring data in MSP430G2553 flash memory
Hello,We are using MSP430G2553 as controller in our project and we need to store 66 bytes of memory (as 64 + 2 bytes) which should be retained even after power is off.We found INFO segments in the...
View ArticleLSM9DS1 Library for MSP430F5xxx
Hi all,I'm working on the ST LSM9DS1 sensor, my setup contains a MSP430F5529LP and a simple LSM9DS1 breakout board.I found some examples on arduino. but I'm asking if there are some software works on...
View ArticleClik here to view.
MSP430F5528 rev. F issue with JTAG - doesn't work
We have a device based on MSP430F5528 MCU. It works fine with F5528 revision H and I. But recently we purchased F5528 revision F (see the picture below) and it doesn't work via JTAG. MCU doesn't...
View ArticleProgramming blues
I have been developing an application "Boosterpack" board for the MSP-EXP430F5529LP Launchpad board. During normal running operations things are hunky-dunky. During a programming phase, however, I...
View ArticleEVM430F6779 - getting raw value - interface with PC
Object:- Collect instantaneous values by time when required(raw values of voltage and current) (Ex: 40 times/sec)- PC sends command to read those values for calculating work.But I am new to MSP430 and...
View ArticleMSP430FR5959 strange behavior at 16 MHz connected to debugger
I have some very odd behavior while trying to debug my program on an MSP430FR5959. I'm using the MSP430FR595x (HFXT Only) variant with a 16 MHz oscillator. When I try and debug the program the debugger...
View ArticleMSP430F2618 opt_for_speed setting changes __delay_cycles() duration
I have an MSP430F2618 executing at 16MHz.As part of my initialization sequence, I would like to debounce a signal that is on a noisy line and susceptible to transient value changes.To help with this,...
View ArticleMSP430F5529 - Error: No USB FET was found
So...I may have accidentally unplugged during an active debug (not 100% positive though as I was in a rush).But I am positive that the PC is now not "seeing" the MSP430.When I plug in the MSP430 it...
View ArticleHow to awake the MCU from LPM3?
Dear freindsYou may saw the piece of code that I am inserting below in other discussions, but I really need you help as I am stuck and not making any progress . I am doing using MSP430g3553 to...
View ArticleMSP-EXP430FR5994 + BOOST- CC2564 MODA
Is it possible to combine the Launch Pad MSP430-EXP430FR5994 with the BOOST.CC2564MODA Board for very low speed Bluetooth 4.0 communications like a Fitnnes Tracking watch?
View ArticleUnable to load U-boot for AM3351 processor
Good afternoon,I'm following the guide http://processors.wiki.ti.com/index.php/Sitara_Linux_Training:_uboot_linux_debug_with_ccsv5 but I'm not able to load the u-boot program after loading the SPL...
View Articlemps430f5529 I2C to MPU6050 help
Any help figuring out how to get i2c working with the MPU6050 would be appreciated.or some tutorials to follow for the msp430F55 series.What's the best way to debug serial communication, just print the...
View Article